Save 20% with Code JUN20 | $3k+ save 25% with Code JUN25
Cart 0

Lava Tile Installation and Care

Shop Lava Tile >

Overview

Read all instructions before ordering and starting the installation.  Contact us if you would like a referral to a professional installer in your area. Lava tiles are designed to provide lasting beauty for decades.  

Applications

Tesselle Lava Tiles can be installed on walls and floors, indoors or outdoors. Ensure that there will be proper drainage.

Before Installation

  • Inspect your tiles.
  • Each tile is unique, and color will vary from tile to tile.
  • Store in a moisture-free environment, and allow tiles to dry prior to installation. 
  • Remove any residue on the tile with a clean cloth.
  • Tesselle is not responsible for product that has been altered. 

Installation

  • Please read our California Proposition 65 Information and wear a face mask that prevents inhalation of dust particles while handling the tiles during unboxing, cutting and installation.
  • Tiles must be installed over a flat, level, stable and dry surface. Moisture, water evaporation or excess of water can cause stains or cracking on the tile surface;  this is a natural reaction of cement-based products.   Make sure that subfloor is fully cured.
  • A waterproof membrane is recommended in all wet areas to prevent leakage of water to spaces below or the subfloor.
  • Do not install during excessively hot weather or in full, direct sun.
  • Mix tiles from different boxes during the installation process.
  • We recommend installing the center tiles first.
  • Tiles look best with a joint width of 1/16".
  • Tiles should be cut using a sharp diamond blade in conjunction with water to avoid chipping of edges.
  • Use a high quality thin-set adhesive based in cement, such as a Laticrete or Mapei products.
  • Make sure that adhesive is applied with full coverage on the back of each tile.
  • Level the tiles with hand pressure, not a mallet
  • Remove excess adhesive from the surface with a damp cloth or sponge when it is fresh to avoid any stains.
  • Handle tiles with extreme care, and make sure that they are kept in a clean environment until sealer is applied.
  • Tip: if your cement tiles are being installed next to a material of a different thickness, Schluter makes a variety of attractive products to address these transitions, such as Schiene Finishing Edge.

Sealing and Grouting

  • Allow tiles and mortar bed to dry out completely, uncovered, before starting to seal the tiles.
  • Do not step on tiles until mortar bed is dried.
  • Seal tiles prior to grout application.  Select a penetrating sealer. If you want to maintain the look of the raw tile, we recommend Miracle 511 Porous Plus or Stain Proof by Dry Treat.  If you would like to enrich the colors and make them look darker, we recommend Miracle 511 Seal & Enhance.  Test on a single tile first.  Apply two coats, allowing each coat to dry completely. Follow manufacturer instructions.  Never apply abrasion. 
  • If applying grout, choose a non sanded type, such as Custom Polyblend that is free of any dye in a shade that is no darker than the lightest color in your tile design
  • Once grout starts to dry, remove excess grout immediately. Do not affix tape. For flooring installations, you may choose to allow the grout to remain in the pores.
  • Clean and re-seal.
  • For high traffic areas, add 2-4 layers of Miracle Mira Matte Sealant. A layer of paste wax can be added for extra protection.
  • For installations in pools or fountains, ensure that penetrating sealer is waterproof and additionally apply an acrylic concrete surface sealer on top.

Cleaning

  • Clean tiles with a pH neutral detergent, such as Zep.  We recommend Miracle Liquid Poultice and Miracle Heavy Duty Cleaner (Acid Substitute) for high traffic areas and occasional deep cleaning.
  • Some stains can be removed by hydrogen peroxide.
  • For red wine stains, use Wine Away.
  • For specific, hard-to-clean stains, tiles can be lightly wet sanded with an extra fine sandpaper (400 grit or finer). Use water when sanding to avoid scratching the tiles and to prevent residue from getting into the pores of the tile and grout. This area should be cleaned, allowed to dry completely and then resealed.

Maintenance

  • For ongoing maintenance, clean regularly with a neutral detergent and buff tiles with a soft white pad.  Re-seal and re-wax as needed, as often as every 6 moths for high traffic areas.
  • Clean spills and stains immediately.  
  • A natural patina will occur as the floor is maintained and wears.
  • Avoid water accumulation

Shop Lava Tile >